How to Make Snowflake Resin Jewelry Tutorial

Making resin jewelry is a lot of fun. It can get addictive, too because there is always more designs you can do. I came up with this lightweight snowflake resin jewelry tutorial to showcase some ways of getting wonderful color backgrounds and effects. These happen to use snowflake shapes but other designs using these steps here are definitely possible!

Paper punch I used a 1 circle punch

Shrinky Dink (shrink plastic ) unshrunk

2 part epoxy resin with cups, stir sticks

*Purchased or review items fromLittle Windows

Snowflake elements used included stickers, punches and metal filigrees. If you plan to use plain white paper, please be aware the resin will make it look translucent. So you need to seal it first to make it impervious to the resin. Stickers sometimes come with little adhesive pads. These are great to have as it makes the snowflakes look like they are floating in the resin.

Also cut up all the shapes you will need in the size which best suits the snowflake elements you will use. Resin film is easily cut by sandwiching it between a folded piece of paper and a paper punch.

Same with the Shrinky Dink plastic. Important :There are two different surfaces to the Shrinky Dink plastic. If resin gets on the rough side, the disc basically becomes transparent. Resin on the smooth side leaves the disc with a slightly translucent texture. So choose which you prefer.

For interesting crinkly backings, crush some aluminum foil. Smooth it out flat and then punch out the discs carefully.

If you dont have a punch, use a template and cut out the shapes by hand. Shown below is the medium size template for Little Windows molds.

Make sure everything you need is all cut up and ready to go before mixing up a batch of resin. It helps to have more projects to do than you think you need in order to use up the resin for each session.

Follow the instructions with the resin kit. In my case, equal portions of part A and B are poured into the mixing cup. Premark the levels with marker pen. Why? You cannot see the cups marks once you pour the solutions in! Thorougly mix for 2- 2.5 minutes.

Let the mix rest for a few minutes before use. This is to allow many of the bubbles to rise. Use the stir stick and coax them to the side to pop them.

Once cast, the pieces have to cure for 12 hours before you can handle them for further work. Allow 48 hours for full curing.

Press the snowflake stickers onto the resin film discs.

Add a drop of resin on each disc and carefully place the snowflake and resin film on it.

Carefully position the top film over the Shrinky Dink disc and adjust the position with the stir stick.

Now slowly add resin to dome up the shape. The weight of the resin will help spread that drop of resin below the resin film. Check for doming completion by looking at the pieces from the side.

Cover to prevent dust from settling on the pieces while you set it aside to cure. Plastic lids from card boxes are excellent for this,

Adding a foil backing and/or doming after the resin has cured is optional. Place a drop of resin on the back of the pendant and position the foil backing over it. Use the stir stick to gently press down especially at the edge. Add more resin on top of the foil either just a layer or dome it again. Your choice. Cover and leave to cure fully.

The foil makes for a beautiful background! Use the foil technique for any discs which may have had some drips underneath. Just slice off the extraneous set resin blobs as much as possible and add the foil!

Mark the hole position with a marker pen. Use the hand drill to make holes in the thinner pendants.

Use either pinch bails or a jump ring to attach to regular bails. Glue on bails will also work for foil backed pendants.

Earrings naturally need jump rings and ear wires :

For the pink pendant : first cut a round disc from resin film to fit. Add a drop of resin in the bezel and place the film on top. Make sure to squeeze all the air out from below the film. Add snowflake sticker and top up with resin to dome. (This particular bezel had a lovely etched pattern underneath which shows through the resin film.)

For the blue design : Mix coarse blue and fine gold sprinkles into some resin mix and added a small amount to the bezel. Let the resin set. Then add the snowflake sticker and seal, dome with more resin.

Use molds with release agents to cast shaped pendants. The pendants below were cast in 1 inch molds. The left one looks bigger because the mold was eventually filled to the top. The left pendant started with a mix of resin and blue sprinkles at the bottom of the mold. The right pendant had just a thin layer of clear resin with a resin film disc slipped in to the bottom.

After curing, the cast pendants were removed from the mold. (Bend mold a few times and tap out the casted resin). A snowflake sticker and a metal filigree with a silver ball were added to the depression that normally forms on the top when casting. Resin is then poured into the depression. The resin was added till it domed on the left one. The resin just filled the depression on the right one but with sufficient depth to hold onto the silver ball which still protrudes. The pendants were cured a second time.

Work slowly. Rushing just introduces errors such as overpouring which leads to spills.

It is important to keep the dust off your work especially while curing the resin. But if you have static issues with the resin film just use a swiffer duster to remove the stubborn dust.

No one is perfect. If you had trouble putting on the resin film and need to remove it to start over, clean off the resin with paper towels soaked in isopropanol (rubbing alcohol from the drugstore).

Reduce the chances of spills going to the underside of the piece by applying a light layer of wax to the back. I usedRenaissance Waxwhich is typically used on metal jewelry to prevent tarnishing. You should remove the wax with isopropanol before you dome the other side with resin.

If you wish, after the resin has set, you can sandpaper the edges smoother. Use wet/dry sandpaper and do it underwater to remove the dust problem. Otherwise wear a dust mask.

I do receive a small fee for any products purchased through affiliate links. This goes towards the support of this blog and to provide resource information to readers. The opinions expressed are solely my own. They would be the same whether or not I receive any compensation.

How to Make a Gold Leaf Resin Bangle Tutorial

Cool Resin Earrings Tutorial Uses Tube Wringer for Corrugated Metal Strips

Bubble Trouble in Resin Jewelry Making

Jewelry Making TipsJewelry Business Tips

You could say Pearl was born to be a jewelry designer with a name like that! She is the author of The Beading Gems Journal now simply calledThe Beading Gem, a popular jewelry making, inspirational and how-to website.Subscribefor your daily dose of tips and tutorials and more

Great tutorial thanks. I usually use a wet wipe to clean up spills and outer edge of bezels and also my hands as I work. Its a fast, efficient method. The ones used for cleaning makeup or baby wipes are particularly helpful.

Yes, I use the wet paper towel route for ongoing messes. It is hard to be neat and tidy sometimes.

Does this type of resin need to be cured at a certain temperature Pearl?

I have a large studio and temperature curing is always a problem especially out here in the West where it is so cold at this time of the year. I just cant keep my studio warm for a long period of time especially overnight.

What an in-depth and detailed tutorial you have given here Pearl!

So much time and effort has obviously gone into this.

Im sure the people at Little Windows appreciate this too! I know I sure do!

Thank you so very much for the most incredible informative year!

It is so obvious that you put your heart and soul into what you do and I just want to thank you for all you do for me!

I really appreciate it! I have learned so much from you!!

LOL! Yes this tutorial did take me a loooong time to do. But then I wanted to give you all the best tutorial I can. Shortcut the learning curve so to speak.

I cure my resin at room temperature which is about 22 deg C in my house. You need a temperature of at least 21 deg C or 70 deg F for the resin to cure see this post

You probably need to move your curing trays to a warmer part of the house.

at Iguana Beads, Cambridge ONCall to book a spotmap

Sign up herefor my special webinar mailing list to learn when the next webinar will be and get information.

How to Make Real Flower Resin Jewelry

Making real dandelion and flower resin jewelry is not technically difficult. But as they say, one learns by doing. I was inspired to try by

How to Make Pressed Flower Resin Jewelry Part 1

You can tell I am having a lot of fun pressing flowers and using them in resin jewelry. I found pressing with a microwave was a lot quicker

Wire Wrapped Prong Set Crystal and Gemstone Jewelry by My Wired Imagination

Florida based Bobbi Maw should really call herself the ring lady! That is because her signature item in her Etsy store, My Wired Imaginatio

How to Dry Dandelion Clocks and Flowers Using Crystal Cat Litter

The Little Windows large cabochon mold (which I received for review) can be used to generate a whole bunch of round resin cabochons in

Winner of Jewelry Affaire Spring 2018 Book Giveaway

Last weeks post about the Spring issue of Jewelry Affaire certainly brought out the boho jewelry lovers! But not everyone had come ac

How to Make Hardware Jewelry Tutorials

I once made some earrings from recycled washers from a decommissioned instrument. These cannot be reused and it seemed such a shame to thro

This site uses cookies. By continuing to use this site, you are agreeing to my use of cookies. Click on the link above to find out more.

COPYRIGHT & PERMISSIONSMy own free tutorials are for your personal use only. Enjoy making them!

You may use one photo and your own words when linking to my original tutorials. Please do make sure you credit me with the link. Duplication of whole posts is not permitted.

If you saw it here first, please acknowledge with a link. Thank you for your cooperation!